1.5 ATA Hyperbaric Chamber: Pressure Level and How to Choose

1.5 How much pressure does ATA represent

ATA is short for atmospheres absolute, which refers to the absolute pressure calculated as the absolute vacuum at zero. 1 ATA is a standard atmosphere of pressure, with an exact value of 101.325 kPa, which is approximately equal to 14.6959 psi. On this basis, the absolute pressure of 1.5 ATA is 151.9875 kPa, or approximately 22.04 psia.

Here too, the absolute pressure and gauge pressure should be distinguished. The gauge pressure is the difference between the pressure in the chamber minus the local atmospheric pressure. Under standard sea level conditions, the gauge pressure corresponding to 1.5 ATA is only about 7.35 psig. That is, a device marked 1.5 ATA, read with gauge pressure, would only have a few psi left at seven. Conversely, if you look at the hyperbaric chamber 12 psi, 12 is usually read by gauge pressure, which translates back to an absolute pressure of about 1.8 ATA up and down, which is one cut above 1.5 ATA. Inconsistent pressure calibers are the easiest way to make mistakes when looking at specifications.

1.5 Position of ATA in the pressure ladder

Line up common specifications and the 1.5 ATA will be more clearly positioned. Down below are 1.3 ata hyperbaric chamber and 1.4 ata hyperbaric chamber, which correspond to gauge pressures of approximately 4.4 psig and 5.88 psig, respectively, at standard sea level. These three 1.3, 1.4, and 1.5 ATA gears all fall into the common range of low-pressure soft pods, and 1.5 ATA is exactly the upper edge of this range.

Looking up, the real dividing line is at 2.0 ATA. Clinical hyperbaric oxygen requires patients to breathe medical-grade oxygen in a hardware compartment at a pressure of not less than 2.0 ATA. Therefore, 2 ata hyperbaric chamber, 2.0 ata hyperbaric chamber, 2 atm hyperbaric chamber, 2 atmosphere hyperbaric chamber, and 2 atmosphere hyperbaric chamber, as well as the inverted hyperbaric chamber 2 ata, hyperbaric chamber 2.0 ata, hyperbaric chamber 2 atmospheres, and hyperbaric chamber 2.0 atmospheres, basically refer to the same threshold. The oxygenated 2.0 ata hyperbaric oxygen chamber and hyperbaric oxygen chamber 2.0 ata also fall into this gear. You need to pay attention to the missing unit writing method of 2.0 hyperbaric chamber. You must first confirm whether it is 2.0 ATA or 2 atmospheres of pressure. Further up, there are higher clinical pressure levels such as 2.4 ata hyperbaric chamber and 2.5 ata hyperbaric chamber.

Put 1.5 ATA back on this line, which is at the junction of the soft and hard compartments: downward is the low-pressure area of the pure soft compartment, and upward is the clinical threshold of 2.0 ATA.

1.5 Product form corresponding to ATA

The 1.5 ATA is special in that it appears in the specification sheets on both the soft and hard compartments. On the soft compartment side, 1.5 ATA is the upper limit of the low-pressure section. Taking MACY-PAN’s products as an example, the pressure specifications of the single-person portable horizontal soft cabin cover 1.3, 1.4 and 1.5 ATA. The cabin body is made of TPU material, weighs about 13 kg, and is about 220 cm long and 80 cm in diameter when unfolded; the widened horizontal cabin also covers these three pressure levels and increases in diameter to 90 cm. The inverted writing of hyperbaric chamber 1.5 ata, or hyperbaric oxygen chamber 1.5 ata with emphasis on oxygen supply, refers to the 1.5 ATA specification in this type of low-pressure software cabin.

On the hardware compartment side, 1.5 ATA is the starting point. The pressure specifications of the stainless steel-based rigid horizontal cabin usually start from 1.5 ATA and are more concentrated in 2.0 ATA; while the vertical and multi-person rigid cabin are basically designed according to 2.0 ATA. So it’s also 1.5 ATA. One may be a foldable soft cabin, and the other may be a fixed-mount stainless steel hardware cabin. The two are very different in structure, oxygen supply method and use. Because 1.5 ATA is this watershed, when choosing a model, you must first distinguish whether you are looking at software or hardware.

What to check when buying 1.5 ATA equipment

After locking the 1.5 ATA pressure, there are a few things to confirm item by item. To distinguish whether ATA is absolute pressure, psi is gauge pressure or absolute pressure, it is best to let the supplier give the full conversion. The complete parameters cannot be represented by just one 1.5 ATA figure either, and one device should also indicate the normal operating pressure, the maximum permissible operating pressure and the set pressure of the pressure relief device.

Higher pressure does not automatically mean better fit or safer. Target pressures must be assessed together with the intended use, structural design, oxygen supply method, operating instructions, and professional supervision requirements. The 1.5 ATA is still below the 2.0 ATA threshold required for clinical hyperbaric oxygen. Based on the pressure figures alone, neither software nor hardware can be used as a clinical treatment module; the US market can query the 510(k) records of specific devices by product code CBF, and note that 510(k) cleared and FDA approved are two different things.

Finally, back to the usage scenario. The soft 1.5 ATA cabin needs to be operated according to the specific model instructions, continuously monitored by qualified personnel, and equipped with fire protection and grounding measures in a high-concentration oxygen environment; the hard cabin needs to verify the installation conditions and professional management requirements. When you compare pressure, structure, use and compliance status, the 1.5 ATA specification is truly selected and understood.